Power cord contact failure
Power cord contact failure
During a 2700 mile trip my Zumo 390 stopped making electrical connection. On examination of the power cable contacts one of the gold dots has been worn down. I suspect that this is due to a less than snug fit in the cradle and the vibration in my Motorcycle's handle bars. I have the same mounts on 2 other bikes and this has not happenned but these two bike have less vibration in the bars. Has anyone else had this problem and does anyone have suggestions on how to isolate the cradle from vibration. I am going to replace the mount but with some foam rubber between the Garmen cradle and the Ram mount unless anyone has a better idea. Sorry about the ppor picture.
- Attachments
-
- ZumoCord.jpg (37.53 KiB) Viewed 1922 times
-
- Posts: 2357
- Joined: Sat Oct 19, 2019 4:17 pm
- Location: West Yorkshire, Uk
- Has liked: 294 times
- Been liked: 638 times
Re: Power cord contact failure
Did you get this sorted ? The contacts are sprung... it may be that some electrical cleaner or solvent and a little agitation may solve it.
Have owned Zumo 550, 660 == Now have Zumo XT, 595, 590, Headache
Use Basecamp (mainly), MyRouteApp (sometimes)
Zumo 590, 595 & Basecamp pdf link
Zumo XT & BC Link
Today, I discovered something really important. I found another way that doesn't work.
Use Basecamp (mainly), MyRouteApp (sometimes)
Zumo 590, 595 & Basecamp pdf link
Zumo XT & BC Link
Today, I discovered something really important. I found another way that doesn't work.
Re: Power cord contact failure
I am sorry for the late reply. I was on a 6000 mile trip and not checking the forum.
I replaced the electrical harness with a new one. I shimmed the crade with some electrical tape to make a tighter fit. I had no problems during the 6000 mile 18 day trip so I believe all is well.
I replaced the electrical harness with a new one. I shimmed the crade with some electrical tape to make a tighter fit. I had no problems during the 6000 mile 18 day trip so I believe all is well.
- twowheelstom
- Posts: 196
- Joined: Tue May 29, 2018 7:00 pm
- Location: Nova Scotia
- Has liked: 5 times
- Been liked: 20 times
Re: Power cord contact failure
If the problem it with the 2 sprung cable power pins getting stuck in its sleeve, can you use WD40 on the pins to lubricate them from getting stuck again?
2005 Kawasaki 800 cruiser Zumo XT
- Peobody
- Subscriber
- Posts: 1370
- Joined: Tue Apr 20, 2021 1:33 pm
- Location: North Carolina USA
- Has liked: 102 times
- Been liked: 291 times
Re: Power cord contact failure
One of the power pins on my XT cradle looked like that but would pop back out when I centered it using my fingernail, only to get stuck back in again. Contact cleaner and silicone spray didn't help. A close examination revealed that the ring within which the pin sits was split allowing the pin to tip sideways when pressured rather than sliding in and out like it should have. The cable had to be replaced.twowheelstom wrote: ↑Sun Dec 31, 2023 7:08 pm If the problem it with the 2 sprung cable power pins getting stuck in its sleeve, can you use WD40 on the pins to lubricate them from getting stuck again?
2008 Honda GL1800 Goldwing
1995 Kawasaki ZG1000 Concours
zūmo XT linked to Cardo Packtalk Bold and iPhone SE.
1995 Kawasaki ZG1000 Concours
zūmo XT linked to Cardo Packtalk Bold and iPhone SE.
- twowheelstom
- Posts: 196
- Joined: Tue May 29, 2018 7:00 pm
- Location: Nova Scotia
- Has liked: 5 times
- Been liked: 20 times
Re: Power cord contact failure
in your opinion, is pins sliding within split rings common on xt cables? i wonder if that split ring came like that from the factory
2005 Kawasaki 800 cruiser Zumo XT
- Peobody
- Subscriber
- Posts: 1370
- Joined: Tue Apr 20, 2021 1:33 pm
- Location: North Carolina USA
- Has liked: 102 times
- Been liked: 291 times
Re: Power cord contact failure
I wouldn't call it a "split ring". It's a solid ring, maybe a shallow sleeve that the pins slides in, spring tensioned from the back. I'm sure it didn't come from the factory that way. I wonder if I caused the problem by wiping rain and dew off of it each morning on our last trip. I kept forgetting to put its cover in place. I was fortunate in that Garmin had redesigned the cable and I had the old design. They sent me a new design one at no charge. The pin design on the new one doesn't look any different so I'll be a lot more careful.twowheelstom wrote: ↑Sun Dec 31, 2023 9:48 pm in your opinion, is pins sliding within split rings common on xt cables? i wonder if that split ring came like that from the factory
Edit: The sleeve/ring that I am referring to is brass looking. I don't see it the picture so the pin design on the XT cable my be different.
2008 Honda GL1800 Goldwing
1995 Kawasaki ZG1000 Concours
zūmo XT linked to Cardo Packtalk Bold and iPhone SE.
1995 Kawasaki ZG1000 Concours
zūmo XT linked to Cardo Packtalk Bold and iPhone SE.